Productos Industriales

VDK 200 A S02 Dungs: Control de Estanqueidad

Dungs

Comparte en Redes

Categoría:

Descripción

VDK 200 A S02 Dungs: Control de Estanqueidad is the compact valve monitoring system as per EN 1643 for automatic shut-off valves:

  1. Device operates independent of inlet pressure
  2. Test volume ≤ 20 l – Setting possible on site
  3. The complete test procedure is defined – Release time: max. 26 s
  4. Tightness or leaks are displayed by an LED
  5. Suitable for TRD systems
  6. Electrical connection at screw terminals via PG 11 cable entry

VDK 200 A S02 Valve proving system for automatic shut-off valves as per EN 161, Class A

Approvals

  1. EC type test approval as per EC Gas Appliance Directive:
  2. VDK 200 A… CE-0085 AQ 0808 EC type test approval as per EC Pressure

Equipment Directive:

VDK 200 A… CE0036 Approvals in other important gas-consuming countries. Special design for the North American market with UL, FM and CSA registration.

Tabla de Selección VDK 200 A S02 Dungs: Control de Estanqueidad

VDK 200 A S02 type overview / accessories / order details
Version Order No.
VDK 200 A S02  230 VAC 50 Hz  211 222
VDK 200 A S02 110 VAC 50 Hz 211 224
VDK 200 A S02 240 VAC 50 Hz 211 229
VDK 200 A S02 120 VAC 60 Hz 211 927
Hydrogen version   For specifications, refer to datasheet 8.12

Ficha técnicaClick aquí

Productos Relacionados – ● VPS S06 Dungs: Control De EstanqueidadSeñalizador De Posición De Válvulas Dungs- Serie K01/1 ● VPS 504 Dungs: Control De EstanqueidadVálvula De Prueba Para Manometros – Dungs

VDK 200 A S02 Dungs: Control de Estanqueidad de venta aquí, contacta a alguno de nuestros asesores dentro del chat o marca al número de sucursal más cercano a ti, será un placer atenderte.

Comparte en Redes

📌 Tabla de Selección

VDK 200 A S02 type overview / accessories / order details
Version Order No.
VDK 200 A S02  230 VAC 50 Hz  211 222
VDK 200 A S02 110 VAC 50 Hz 211 224
VDK 200 A S02 240 VAC 50 Hz 211 229
VDK 200 A S02 120 VAC 60 Hz 211 927
Hydrogen version   For specifications, refer to datasheet 8.12

Comparte en Redes

📋 Especificaciones básicas

Operating pressure max. 360 mbar (36 kPa)
Test volume ³ 0,4 l
≤ 20,0 l
Rated voltage / frequency (admissible voltage range) 230 V AC -15% to -240 V +6% 50 Hz

For further voltages, refer to type overview

Power requirements During pumping time approx. 80 VA, in operation 20 VA
Back-up fuse (provided by customer) 10 A fast-blow fuse or 6.3 A slow-blow fuse
Fuse installed in housing cover, re- Microfuse T 6.3 L 250 V; IEC-127-2/III (DIN 41 662)
Switching current Operation output Terminal 13: max. 4 A
Observe the starting current of the motor! Fault output  Terminal 14: max. 1 A
Degree of protection IP 40
Ambient temperature -10 °C to +60 °C
Release time 10…26 s, depending on test volume and inlet pressure
Interference time 32 ± 3 s
Sensitivity limit 50 dm3/h or 0.1 % of the burner heat load (> 500 kW) The VDK 200 A S02 can always be used with systems with a burner capacity < 500 kW or a test volume < 6 l. If the system has a burner capacity > 500 kW or a test volume > 6 l, the VDK 200 A S02 can be used only if the burner capacity is higher than the minimum burner capacity specified in the diagram.
Switch-on duration of control 100%
Max. number of test cycles 15/h. Wait for at least 2 minutes after carrying out more than 3 consecutive test cycles.
Installation position vertical to horizontal, not upside down

 

Comparte en Redes

☑ USOS / APLICACIONES

Valves according to EN 161 Class A

The VDK 200 A S02 may be used with any other valve whose tightness in counter-flow direction excludes by construction a leakage in flow direction.

The VDK 200 A S02 is suitable for all DUNGS valves according to EN 161 Class A.

For special model for H2 applications, refer to data sheet 8.12. Suitable for gases of gas families 1, 2, 3 and other neutral, technical burnable gases.

Comparte en Redes

📑 Ficha técnica


225665.pdf (566 KB)

Comparte en Redes

👷 Instrucciones de operación y montaje.


223949.pdf (892 KB)
223925.pdf (888 KB)

Comparte en Redes

✔️ Certificación

CE-0085AQ0808.pdf (352 KB)
Pressure Equipment Directive DGR-008.pdf (423 KB)
EAC-Valve-Proving-Systems.pdf (163 KB)
UA-Ventilpruefsysteme.pdf (1,004 KB)

 

Comparte en Redes

🎥 Video

 

Comparte en Redes

Valoraciones

No hay valoraciones aún.

Sé el primero en valorar “VDK 200 A S02 Dungs: Control de Estanqueidad”

Tu dirección de correo electrónico no será publicada. Los campos obligatorios están marcados con *

Visitanos en Redes Sociales

Sígueme en Facebook Sígueme en Facebook Sígueme en Flickr! Sígueme en instagram! Sígueme en youtube!
shares
es_MXSpanish
es_MXSpanish
0